The root user on a fresh Debian VPS has the default password “rootroot”.
After logging in to your VPS for the first time, please change this password to something more secure. Type
passwd at the prompt and follow the instructions. Don't forget this password as there is currently no way to recover it.
It is a good habit to create a regular user account for working, using
su to obtain root privileges as needed. To create a regular user account:
useradd -m <username>
This user will be able to perform administrative tasks by runing
su to obtain superuser privileges using the root password.
In your control panel at vps.sdf.org, note YOUR_IP (e.g. 184.108.40.206) on the top line, and YOUR_HOSTNAME (e.g. debian99).
Start your server, and log in via the console. (default= root:rootroot)
Open /etc/network/interfaces in an editor and add the following, replacing the text YOUR_IP with your own actual IP number, add:
auto eth0 iface eth0 inet static address YOUR_IP netmask 255.255.255.0 network 220.127.116.11 broadcast 18.104.22.168 gateway 22.214.171.124 dns-nameservers 126.96.36.199
Note: For VPS installations of Debian 8.4 (jesse) on VPS3, please omit the above dns-nameservers line from the interfaces file, and instead add this line to /etc/resolv.conf:
Add this to /etc/hosts:
YOUR_IP YOUR_HOSTNAME.sdf.org YOUR_HOSTNAME
Change /etc/hostname to:
You may wish to add ssh access to your VPS. It is highly recommended that you disable root login via ssh and use a normal user account to login.
apt-get install openssh-server
Edit /etc/ssh/sshd_config and change the line:
Now restart sshd by running/typing:
You can now test ssh by running
Refer to the following article to see how to clean up (remove packages) from your VPS:
# echo "blacklist ipv6" >> /etc/modprobe.d/blacklist
# vi /etc/firewall
*filter -A INPUT -i lo -j ACCEPT -A INPUT ! -i lo -d 127.0.0.0/8 -j REJECT -A OUTPUT -j ACCEPT -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT -A INPUT -p tcp --dport 80 -j ACCEPT -A INPUT -p tcp -m state --state NEW --dport 22 -j ACCEPT -A INPUT -p icmp -m icmp --icmp-type 8 -j ACCEPT -A INPUT -m limit --limit 5/min -j LOG --log-prefix "iptables denied: " --log-level 7 -A INPUT -j REJECT -A FORWARD -j REJECT COMMIT
Load rules (now):
# iptables -F # iptables-restore < /etc/firewall
Load rules (boot):
# vi /etc/network/if-pre-up.d/firewall #!/bin/sh /sbin/iptables-restore < /etc/firewall # chmod 755 /etc/network/if-pre-up.d/firewall
To update your system, run the following commands:
apt-get dist-upgrade -y
If you are using a 128MB slice, it's a good idea to reduce the memory usage of some processes or even disable them.
You might not need one or both of those, so you can deactivate them with
# update-rc.d -f atd remove # update-rc.d -f cron remove
This frees up ca. 7MB (if both are deactivated).
This being a virtual system, you won't need getty on tty1-6. In order to eliminate them, edit /etc/inittab and modify the corresponding lines like this:
co:2345:respawn:/sbin/getty hvc0 9600 linux #1:2345:respawn:/sbin/getty 38400 tty1 #2:23:respawn:/sbin/getty 38400 tty2 #3:23:respawn:/sbin/getty 38400 tty3 #4:23:respawn:/sbin/getty 38400 tty4 #5:23:respawn:/sbin/getty 38400 tty5 #6:23:respawn:/sbin/getty 38400 tty6
You need to keep the line with hvc0 so you can attach a serial console from vps.sdf.org to your vps. This frees up ca. 10MB.
rsyslogd eats a lot of memory by default (26MB on my vps) which can be reduced by the usage of ulimit. Edit /etc/init.d/rsyslog and include the following line just before the command where rsyslogd will be started:
ulimit -s 256
case "$1" in start) ulimit -s 256 log_daemon_msg "Starting $DESC" "$RSYSLOGD" create_xconsole do_start case "$?" in 0) sendsigs_omit log_end_msg 0 ;; 1) log_progress_msg "already started" log_end_msg 0 ;; *) log_end_msg 1 ;; esac ;;
This frees up about 23MB.
I don't need portmap, so i removed it completely:
apt-get remove --purge portmap
If you dont need all the extra features openssh has compared to dropbear, you can reduce memory consumption from 23MB to 5MB while being connected with 1 non-root user to the system by replacing openssh with dropbear.
apt-get install dropbear
Edit /etc/defaults/dropbear and set NO_START to 0 and add the extra args “-w -s -g” to disallow root and password logins (You'll be only able to login with a non root user and ssh keys):
# disabled because OpenSSH is installed # change to NO_START=0 to enable Dropbear NO_START=0 # the TCP port that Dropbear listens on DROPBEAR_PORT=22 # any additional arguments for Dropbear DROPBEAR_EXTRA_ARGS="-w -s -g" # specify an optional banner file containing a message to be # sent to clients before they connect, such as "/etc/issue.net" DROPBEAR_BANNER="" # RSA hostkey file (default: /etc/dropbear/dropbear_rsa_host_key) #DROPBEAR_RSAKEY="/etc/dropbear/dropbear_rsa_host_key" # DSS hostkey file (default: /etc/dropbear/dropbear_dss_host_key) #DROPBEAR_DSSKEY="/etc/dropbear/dropbear_dss_host_key" # Receive window size - this is a tradeoff between memory and # network performance DROPBEAR_RECEIVE_WINDOW=65536
Afterwards, you can deactivate openssh with
update-rc.d ssh remove
or uninstall it:
apt-get remove openssh-server