sdf_s_vpn_servers
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
sdf_s_vpn_servers [2021/03/21 00:13] – [PPTP Kernel Module] hc9 | sdf_s_vpn_servers [2021/03/21 00:29] (current) – [Connecting in FreeBSD] hc9 | ||
---|---|---|---|
Line 269: | Line 269: | ||
- Login to your OpenWRT device via SSH. | - Login to your OpenWRT device via SSH. | ||
- Install the required userspace tools and module for MPPE: //opkg install pptp kmod-mppe// | - Install the required userspace tools and module for MPPE: //opkg install pptp kmod-mppe// | ||
- | - Follow the [[#linux|Linux]] directions above like normal. | + | - Follow the [[#connecting_in_linux|Linux]] directions above like normal. |
- If you are still having trouble, look over the official OpenWRT documentation found here: http:// | - If you are still having trouble, look over the official OpenWRT documentation found here: http:// | ||
===== Connecting in FreeBSD ===== | ===== Connecting in FreeBSD ===== | ||
- | * Install mpd4 from ports or packages. | + | * Install |
- | * Add the following section to your / | + | * Add the following section to your '' |
- | + | ||
- | < | + | |
sdfvpn: | sdfvpn: | ||
new -i ng1 sdfvpn sdfvpn | new -i ng1 sdfvpn sdfvpn | ||
Line 310: | Line 307: | ||
set ccp yes mpp-stateless | set ccp yes mpp-stateless | ||
open | open | ||
- | |||
</ | </ | ||
- | |||
* You will have to replace three (3) things in this config: | * You will have to replace three (3) things in this config: | ||
- Your USERNAME | - Your USERNAME | ||
- Your PASSWORD | - Your PASSWORD | ||
- | - The local address of SDF's VPN host. This can be found in /etc/hosts on SDF. The local IP will start with 10.0.0, but have the same last octet as the public IP. | + | - The local address of SDF's VPN host. This can be found in '' |
- | + | ||
- | * Add this in your / | + | |
- | + | ||
- | < | + | |
+ | * Add this in your ''/ | ||
sdfvpn: | sdfvpn: | ||
set link type pptp | set link type pptp | ||
Line 327: | Line 319: | ||
set pptp enable originate outcall | set pptp enable originate outcall | ||
set pptp disable incoming | set pptp disable incoming | ||
- | |||
</ | </ | ||
- | |||
* You will have to replace one (1) thing in this config: | * You will have to replace one (1) thing in this config: | ||
- | - The public address of SDF's VPN host. You can get this by running setvpn at the shell. | + | - The public address of SDF's VPN host. You can get this by running |
- | * Now, as root, run mpd4 sdfvpn. | + | * Now, as root, run '' |
* You should now be connected to SDF over a layer 3 tunnel across the Internet. | * You should now be connected to SDF over a layer 3 tunnel across the Internet. | ||
* Your new routes are only for SDF's hosts, and use their internal IP addresses. These are the 10.0.0.x ones. I'm working on how to route to the public ones over the VPN without creating a routing loop to the VPN host. I copied SDF's /etc/hosts file to my machine so that I can run 'ssh sdf1' to connect through the tunnel. | * Your new routes are only for SDF's hosts, and use their internal IP addresses. These are the 10.0.0.x ones. I'm working on how to route to the public ones over the VPN without creating a routing loop to the VPN host. I copied SDF's /etc/hosts file to my machine so that I can run 'ssh sdf1' to connect through the tunnel. |
sdf_s_vpn_servers.1616285608.txt.gz · Last modified: 2021/03/21 00:13 by hc9