DokuWiki

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== Using Multiple Interactive Programs on TWENEX ======

December 28, 2011

TOPS-20 allows you to use multiple interactive programs simultaneously from a single login session. For example, in the middle of editing a document you can run other programs or commands, lookup help files, refer to e-mail messages, etc., and then return to your editing session in the same state you left it.

(Multiple non-interactive programs can be run using the TOPS-20 batch facility. See the TOPS-20 User's //Guide((TOPS-20 User's Guide. Available on Twenex.org in file DOC:USERS.MEM or on the WWW at http://tilt.twenex.org/.))// chapter 10 "Using Batch".)

The functions described in this tutorial are equivalent to those on Unix systems invoked with the Ctrl-Z key and commands like fg, jobs, etc.

There are two ways to run multiple interactive //programs((It is only necessary to use these methods when you wish to use two or more user programs at the same time. Running a user program from EXEC without first running PUSH or KEEP will overwrite the user program address space and destroy the session state of the previously running program. However, EXEC commands generally do not disturb user program address space. You can halt an active program (with ^C^C), run several EXEC commands (e.g. DIRECTORY, HELP, TYPE), and return to your original program (with CONTINUE) in the state you left it.))// in TOPS-20:

  - Push/Pop: From an interactive session you run another program, then return to the first program when the called program is complete.
  - Multiforking: You run two or more interactive programs in parallel and switch among them as needed, preserving the program session state from the last time you visited the program.

===== Push/Pop =====

This method involves starting a new EXEC command level subordinate to your login EXEC. The state of your original program is preserved in your login EXEC while you run one or more programs in the child EXEC level. When done, you terminate the child EXEC and return to your original program.

<file config EXEC>

  *^C			! Return from program session to EXEC
  ^C			! (only single ^C will echo).

  @PUSH			! Start child EXEC instance.

   TOPS-20 Command processor 7(4168)-1
  @MM                   ! Start a program in the child EXEC.

  ...			! Use program then exit.

  @POP			! Terminate child EXEC and return to
  			! parent EXEC.

  @CONTINUE(3)		! Return to original program session.
  *			! Depending on the program you may
  			! continue entering commands or
  			! refresh the display.

</file>

===== Multiforking =====

With multiforking, you run multiple programs in the same EXEC by forking a separate address space to maintain each program's state. You can then move between the forks and their corresponding programs at will. You do not need to end a program before returning to a previously used program session, and may revisit any of the forked programs multiple times preserving each program's session status.

<file config EXEC>
  *^C			! Return from program session to EXEC
  ^C			! (only single ^C will echo).

  @KEEP			! Create separate address space for
  			! new program.

  @MM                   ! Start new program.

  ...			! Use program.

  MM>^C			! Return from second program to EXEC.

  @INFORMATION FORK-STATUS
  			! List forks in current EXEC.
  			! (Current fork marked with "=>".)

      TECO (1): Kept, ^C from IO wait at TYI+3, 0:00:00.0
   => MM (2): ^C from IO wait at $COMND+3, 0:00:00.0

  @FORK TECO		! Switch to original program's fork
  			! ("TECO").

  @CONTINUE		! Return to original program session.

  ...			! Use original program.

  *^C			! Return to EXEC.

  @INFORMATION FORK-STATUS
   => TECO (1): Kept, ^C from IO wait at TYI+3, 0:00:00.0
      MM (2): ^C from IO wait at $COMND+3, 0:00:00.0

  @FORK MM		! Switch to second program fork ("MM").

  @CONTINUE		! Resume second program session.

</file>

^EXEC snippet, and end-note link:^
|//@INFORMATION FORK-STATUS((EXEC commands and options may be abbreviated to the minimum unique prefix, for example:
<file config EXEC abbreviated>
  CONTINUE			=> CONT
  INFORMATION FORK-STATUS	=> IN FO
</file>))//|
===== More Information =====

More information can be found in TOPS-20 User's //Guide((TOPS-20 User's Guide. Available on Twenex.org in file DOC:USERS.MEM or on the WWW at http://tilt.twenex.org/.))// sections 8.6 "Running Programs Without Destroying Memory" and 8.7 "Running Multiple Programs".

===== Notes =====

<del>[1] TOPS-20 User's Guide. Available on Twenex.org in file DOC:USERS.MEM or on the WWW at http://tilt.twenex.org/.</del>

<del>[2] It is only necessary to use these methods when you wish to use two or more user programs at the same time. Running a user program from EXEC without first running PUSH or KEEP will overwrite the user program address space and destroy the session state of the previously running program. However, EXEC commands generally do not disturb user program address space. You can halt an active program (with ^C^C), run several EXEC commands (e.g. DIRECTORY, HELP, TYPE), and return to your original program (with CONTINUE) in the state you left it.</del>

<del>[3] EXEC commands and options may be abbreviated to the minimum unique prefix, for example:
</del>
<file config EXEC abbreviated>
  CONTINUE			=> CONT
  INFORMATION FORK-STATUS	=> IN FO
</file>

----

$Id: twenex-multiprg.html,v 1.2 2011/12/28 09:43:56 papa Exp $ [[http://sdf.org/?tutorials/twenex-multiprg|Using Multiple Interactive Programs on TWENEX]] - traditional link (using [[wp>Revision_Control_System|RCS]])